Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

CNTs/Polyester复合材料的微波吸收特性研究

研究了添加不同质量分数CNTs的聚酯基复合材料的电磁波吸收性能,初步分析了CNTs的螺旋结构和手征性质导致8～40GHz波段良好的吸收。其中厚度为1.40mm±0.05mm的CNTs/Polyester复合材料在25GHz有较强的吸收峰。     

Modeling of Material Deformation Kinetics in the Prefracture Zone

Based on the concept of complete stress–strain diagrams, we propose a new model describing the law of stress distribution in the prefracture zone in plastic materials in view of the type of the stressed state.     

铜蒸气激光器种子注入光腔的参数计算

用矩阵光学理论计算了由主振荡器和功率放大器组成的种子注入光腔。主振荡器光腔是由曲率半径R1=-250mm,R2=5000mm,相距L=2375mm的球面镜组成的正支非稳腔;功率非稳腔是由曲率半径R3=400mm,R4=5600mm,相距S=3000mm的球面镜构成的负支非稳腔。理论计算表明,该种子注入光腔可输出光束发散角约几十微弧的激光,可满足铜蒸气激光器主振荡器功率放大器(MOPA)的技术要求。     

Synthesis and luminescence of Sr2CeO4 fine particles

Fine particles of a blue emission phosphor Sr₂CeO₄ have been synthesized using a chemical co-precipitation technique, and the textual and luminescent properties were compared with the one synthesized by the conventional solid-state reaction method. Particle size and distribution of the Sr₂CeO₄ fine powder prepared by the co-precipitation process were smaller and narrower than those obtained by the samples prepared from the conventional one. The emission intensity of the fine particles was equal to that of the larger particles prepared from the solid-state reaction, on the contrary to the general tendency that emission intensity decrease with particle size reduction. Although no Ce³⁺ peaks were observed in EPR measurements, X-ray photoelectron spectra of the samples clearly elucidated the existence of Ce³⁺ only on the surface of Sr₂CeO₄.     

A suitable computational strategy for the parametric analysis of problems with multiple contact

The aim of the present work is to develop an application of the LArge Time INcrement (LATIN) approach for the parametric analysis of static problems with multiple contacts. The methodology adopted was originally introduced to solve viscoplastic and large‐transformation problems. Here, the applications concern elastic, quasi‐static structural assemblies with local non‐linearities such as unilateral contact with friction. Our approach is based on a decomposition of the assembly into substructures and interfaces. The interfaces play the vital role of enabling the local non‐linearities, such as contact and friction, to be modelled easily and accurately. The problem on each substructure is solved by the finite element method and an iterative scheme based on the LATIN method is used for the global resolution. More specifically, the objective is to calculate a large number of design configurations. Each design configuration corresponds to a set of values of all the variable parameters (friction coefficients, prestress) which are introduced into the mechanical analysis. A full computation is needed for each set of parameters. Here we propose, as an alternative to carrying out these full computations, to use the capability of the LATIN method to re‐use the solution to a given problem (for one set of parameters) in order to solve similar problems (for the other sets of parameters). Copyright © 2003 John Wiley & Sons, Ltd.     

Atomic layer chemical vapour deposition of copper

Copper films with (1 1 1) texture are of crucial importance in integrated circuit interconnects. We have deposited strongly (1 1 1)-textured thin films of copper by atomic layer deposition (ALD) using [2,2,6,6-tetramethyl-3,5-heptadionato] Cu(II), Cu(thd)₂, as the precursor. The dependence of the microstructure of the films on ALD conditions, such as the number of ALD cycles and the deposition temperature was studied by X-ray diffraction, scanning electron microscopy (SEM), and transmission electron microscopy. Analysis of (1 1 1)-textured films shows the presence of twin planes in the copper grains throughout the films. SEM shows a labyrinthine structure of highly connected, large grains developing as film thickness increases. This leads to low resistivity and suggests high resistance to electromigration.     

Failure analysis of a broken tooth

Several days after heart surgery, a patient discovered his upper right canine tooth had broken at the root. Such tooth damage, recognized post-operatively, is usually assumed to be caused by blunt mechanical force from an instrument used by the anesthesiologist during placement of a breathing tube at the start of surgery. In this case, the patient had saved the crown portion of the broken tooth, and it was possible to examine the root fracture characteristics. The curvature and direction of the crack path and natural tooth situation suggested that failure could be described through a cantilever beam model. This was confirmed when a whole extracted sample tooth was embedded and broken by a measured force in a manner consistent with the model. The resulting fracture surface matched that of the patient’s broken canine tooth. However, the high load and force direction necessary to fracture the root was inconsistent with forces applied during the anesthesia procedure. The failure analysis and further investigation indicated tooth clenching on the breathing tube during recovery was the likely cause of fracture. This paper presents an alternate explanation for intubation-related dental injury, demonstrates the practicality of fractographic analysis of biological materials, and introduces a methodology for simulating in vitro tooth settings for mechanical testing.     

一种新的网络对象存储设备研究

Internet的飞速发展对于存储系统的可扩展性提出了很高的要求,也带来了由数据模型与存储模型的不一致问题引起的服务器性能瓶颈现象.针对这些情况,本文提出了网络对象附属存储设备(NAOSD)的概念,其利用设备处理器的能力直接支持结构化数据存储.这一设计减少了存储系统中数据服务器的负载,增加了系统吞吐量.同时,研究了该设备原型在集群环境中的应用,提出了数据/元数据统一存储与查询式数据定位机制.分析表明,这些机制能够较显著地提高系统扩展性——数据访问时间随系统规模的扩大呈对数增长,优于传统的映射定位机制.我们已经模拟实现了NAOSD,并在性能比较测试中取得了较好的效果.     

锂离子电池正极材料LiMn2O4的研究进展

具有尖晶石相的LiMn2O4因价格低、无毒、无环境污染、制备简单、研究较成熟,因此有着很好的应用前景,被看作最有可能成为新一代商用锂离子二次电池正极材料.由于LiMn2O4电化学循环稳定性能不好,表现在可逆容量衰减较大,尤其在高温下(>55℃)使用衰减更严重,从而限制了它的商业化应用.经过近十几年的研究,人们对其衰减机理有了比较清晰的了解,提出了造成容量衰减的几种可能原因如Jahn-Teller畸变效应、Mn2+在电解质中的溶解、出现稳定性较差的四方相以及电解质的分解等.通过掺杂、表面包覆、制备工艺的改进,人们已能制得循环稳定性能较好的尖晶相材料.本文结合我们研究小组的最新研究成果对锂离子二次电池正极材料LiMn2O4的最新研究进展进行综述和评论.